Skip to content

System Inspection

Heat Pump Inspection in Aurora

Get a written report of actual readings so you know the system’s condition before spending anything.

  • Written Report
  • Altitude-Adjusted
  • No Commitment
A heating engineer works on an outdoor air source heat pump unit in a residential garden.

What Goes Wrong

Why some inspections leave you no better informed than before

Verbal-Only Findings

A spoken summary gives you nothing to compare against a repair quote or a second opinion later.

Documented Readings

Every measurement is written down so you can review findings at your own pace and share them with anyone.

Checkbox Pass-Fail

A pass-or-fail sheet hides how far a reading sits outside rated tolerance, a near-failure looks the same as a clean result.

Actual Values Recorded

The inspector records the real number for each item and notes the manufacturer’s rated spec alongside it.

Altitude Overlooked

At Aurora’s elevation, low refrigerant charge or restricted airflow cuts BTU output faster than it would at sea level.

Elevation-Aware Review

Airflow volume and refrigerant charge are evaluated against altitude-adjusted performance expectations, not flat benchmarks.

No Scope Before Cost

Agreeing to a repair before seeing a written estimate means the final bill can shift well beyond the verbal figure given on site.

Written Estimate First

Any repair or follow-on work is scoped in writing before it is booked, so you approve the cost before anything is scheduled.

How the Inspection Works

A heat pump inspection that produces a written report, not a verbal summary

Knowing the actual condition of the system is the only way to make a sound decision about it.

Request an Assessment

A heat pump inspection checks the components that affect output: refrigerant charge, evaporator and condenser coil condition, airflow volume across the air handler, electrical connections, and thermostat calibration. Each item is measured against the manufacturer’s rated specifications, not a general impression. The inspector records actual readings, not pass-or-fail checkboxes.

At Aurora’s altitude, a unit running with a low refrigerant charge or restricted airflow loses BTU output faster than it would at lower elevations. The inspection identifies those losses before they become a full system failure. You receive a written report of every finding, including any items that fall outside rated tolerances.

The written report gives you a clear picture of the system’s condition before you commit to any repair or replacement spend. We schedule the inspection and coordinate access and timing on your behalf. There are no verbal-only summaries; every finding is documented so you can review it at your own pace.

Why Choose Us

Why Aurora Heat Pumps for your inspection?

Every enquiry starts with a system evaluation and ends with documentation you can act on.

  1. Written Estimate Before Any Work Is Booked

    The full scope and cost go on paper before anything is scheduled, so there are no surprises after the inspection.

  2. Written Estimates Only

    We schedule inspections suited to Aurora’s conditions, not whoever is available nationally.

  3. Coordinated Access & Timing

    We handle scheduling and site access on your behalf, so you are not chasing availability yourself.

  4. Post-Install Check Included on New Work

    Any follow-on installation is confirmed against rated specs with a post-install check before the job is closed out.

A modern heating system manifold with insulated pipes and grey insulation covers against a textured grey wall.
Clean condensing boiler installation with manifold and copper piping basement mechanical room

The Process

From enquiry to written report in three steps

Request an Assessment

  1. Submit Your Details

    Tell us about your system and property so we can schedule the right inspection.

  2. Confirm Access & Timing

    We coordinate the appointment directly, handling scheduling and site access so nothing falls through the gaps.

  3. Receive Your Written Report

    After the visit you get a documented report of all readings and findings, with any out-of-tolerance items clearly noted.

Pricing Estimates

Typical Heat Pump Inspection Prices

JobTypical cost
Basic heat pump inspection$150-$250
Full heat pump inspection$200-$300
These prices are estimates and often vary with the condition, size and scope of each job. Message or call us for a free, no-obligation quote.
See all prices

Common Questions

Questions about heat pump inspections in Aurora

  • What does a heat pump inspection check?

    An inspection covers the outdoor and indoor units, refrigerant-circuit performance, electrical connections, airflow, coil condition, and controls. The technician looks for wear, efficiency loss, and anything that could cause a breakdown. You get a written summary of what is working normally, what is degrading, and what needs attention.

  • Does the inspection cover both the indoor and outdoor units?

    Yes, both units are checked. The outdoor unit is inspected for coil condition, fan operation, and debris buildup. The indoor air handler is checked for airflow, filter condition, and electrical connections. A single-unit check would miss half the system.

  • Do you check airflow, electrical parts, and refrigerant-related performance during the inspection?

    Yes, all three areas are covered. Airflow is assessed at the air handler and across the coil. Electrical connections, capacitors, and controls are inspected for wear or loose contacts. Refrigerant-circuit performance is evaluated through operating pressures and temperature differentials, not just a visual check.

  • Will the report tell me what is normal, what is worn, and what needs repair?

    Yes. The written summary separates findings into three categories: components operating within normal range, parts showing wear that should be monitored, and items that need repair now. That breakdown lets you make an informed decision rather than guessing which findings are urgent.

  • Do I need an inspection if my heat pump still turns on?

    Turning on is not the same as running efficiently. A heat pump can start normally while losing 20-30% of its heating capacity due to low refrigerant charge, dirty coils, or a degraded compressor. An inspection measures actual performance, not just whether the unit powers up.

  • What problems can an inspection help find?

    Common findings include low refrigerant charge, dirty or blocked coils, failing capacitors, loose electrical connections, restricted airflow from a clogged filter or collapsed duct, and defrost-control faults. Any of these can cut heating output significantly or lead to compressor failure if left unaddressed.

  • Could an inspection lead to unexpected repair costs?

    An inspection can reveal repairs you were not aware of, but those costs exist whether or not you inspect. Finding them early usually means a smaller repair bill than waiting for a component to fail completely. Any repair scope is put in writing before work is booked, so there are no surprise charges.

  • Is an inspection a good idea before winter starts?

    Yes, a pre-winter inspection is the most practical time to book one. It confirms the system can handle sustained cold-weather demand before you actually need it. Any repairs found can be scheduled on your timeline rather than as an emergency during the first hard freeze.

  • Which areas do you cover for Heat Pump Inspection?

    We cover Heat Pump Inspection in and around Aurora, including Bennett, CO, Centennial, CO, Foxfield, CO, Mission Viejo, CO, Murphy Creek, CO, Denver, CO, Greenwood Village, CO, Englewood, CO, Parker, CO, Lone Tree, CO and Highlands Ranch, CO. If your area isn’t listed, send us a quick message to check.

Arrange a Heat Pump Assessment

We put the scope in writing before any work is booked. Tell us about your system. We schedule the inspection and document every finding.

Request an Assessment