Skip to content

Aurora Heat Pumps

Air Source Heat Pumps in Aurora

A correctly sized system that keeps up with Colorado winters and pays back on every energy bill.

  • Altitude-Adjusted Sizing
  • Written Estimate First
  • Post-Install Check
Outdoor heat pump condenser unit on concrete pad beside home with refrigerant lines

What Goes Wrong

The sizing mistakes that leave Aurora homeowners with an underperforming system

Most heat pump problems trace back to decisions made before installation day.

Sea-Level BTU Charts

A unit sized from a standard manufacturer chart loses measurable output at Aurora’s elevation, leaving the home under-heated on cold days.

Altitude-Adjusted Load Calc

Every system we arrange is sized after a full BTU load calculation derated for Aurora’s altitude, not copied from a flat chart.

No Backup Heat Plan

Lower-spec units have an operating floor above Colorado’s coldest nights, so a system without a backup heat strategy fails when it matters most.

Freeze Protection Built In

Backup heat strategy is confirmed before installation begins, so the system has a defined response when outdoor temps drop below the unit’s floor.

Vague Verbal Quotes

An informal quote that omits equipment model, scope, or timeline leaves you with no basis to compare installers or hold anyone accountable.

Itemised Written Estimate

We put the equipment model, full scope of work, and expected timeline in writing before any installer is booked, so every detail is on record.

No Output Verification

A system that passes a visual walkthrough but was never tested under actual load can run for months before the shortfall becomes obvious.

Post-Install Performance Check

After installation, a check confirms the system hits its rated output under real load conditions before the job is considered complete.

Air-Source Systems

Air-source heat pumps sized for Colorado’s altitude and winters

Getting the SEER rating right matters less than getting the BTU sizing right first.

Request an Assessment

Air-source heat pumps pull heat from outdoor air, which means performance drops as temperatures fall and as altitude reduces air density. At Aurora’s elevation, a unit rated at a given BTU output at sea level delivers measurably less. Every system we arrange is sized after an altitude-adjusted load calculation, not from a manufacturer’s standard chart.

SEER ratings guide equipment selection once sizing is confirmed. We match the unit to your home’s square footage, insulation level, and duct configuration, then provide a written, itemised estimate before any installer is booked. The estimate states the equipment model, scope of work, and expected timeline so you know exactly what is being arranged.

Freeze protection is built into the plan from the start. Colorado winters can push outdoor temperatures well below the operating floor of lower-spec units, so backup heat strategy is confirmed before installation. A post-install check verifies the system hits its rated output under actual load conditions before the job is closed.

Why Choose Us

Why Aurora Heat Pumps for your air-source installation?

Every step from enquiry to post-install check is handled with a clear paper trail and local knowledge built into the process.

Evaluation Before Anything Else

Every enquiry starts with a load, equipment, and altitude-adjusted sizing review before a single installer is contacted.

Scope in Writing Before Booking

The written estimate covers equipment model, installation scope, and timeline, issued before any work is scheduled.

Local Installers, Aurora Area

We arrange local heat pump installers who work in the Aurora area and know its elevation and climate conditions firsthand.

Post-Install Output Verification

A performance check after installation confirms the system meets its rated output under real conditions before the job closes.

Air-Source, Mini-Split & Geothermal

We handle enquiries across all three system types, so the right technology is matched to your property from the start.

A modern heating system manifold with insulated pipes and grey insulation covers against a textured grey wall.
Clean condensing boiler installation with manifold and copper piping basement mechanical room

The Process

From first enquiry to a verified, running system

Request an Assessment

  1. 01

    Submit Your Details

    Tell us about your home and we arrange a local installer to run an altitude-adjusted load calculation and assess your existing equipment.

  2. 02

    Review Your Written Estimate

    You receive an itemised estimate stating the equipment model, full scope of work, and timeline before any booking is confirmed.

  3. 03

    Install & Verify Output

    The installer completes the work and a post-install check confirms the system hits its rated BTU output under actual load conditions.

Pricing Estimates

Typical Air Source Heat Pumps Prices

JobTypical cost
Single-zone air source heat pump$6,700-$9,500
Standard whole-home air source heat pump$9,920-$14,880
High-efficiency air source heat pump$14,880-$20,000
These prices are estimates and often vary with the condition, size and scope of each job. Message or call us for a free, no-obligation quote.
See all prices

Common Questions

Questions about air-source heat pumps in Aurora

  • Will I need new radiators or a new hot water tank?

    Often, yes. Heat pumps deliver heat at lower flow temperatures than a boiler, so undersized radiators won’t keep rooms warm. Many homes also need a new hot water tank. The heat loss assessment identifies which upgrades are needed before the estimate is written.

  • Will a heat pump keep the house warm enough in a Colorado winter?

    A correctly sized system will. The key is accurate heat loss calculation and a backup heat strategy for the coldest nights. An undersized unit or one without a backup plan is the reason some homes feel cold, not the technology itself.

  • What happens if I delay replacing an aging furnace or boiler?

    An aging system that fails mid-winter leaves you without heat while emergency replacements are arranged, often at higher cost and with fewer equipment options. Scheduling an assessment before a breakdown gives you time to plan the upgrade properly.

  • Is an air source heat pump only for heating?

    No. These systems provide both heating and cooling from a single outdoor unit. The exact setup depends on the equipment selected and how the indoor side is configured during installation.

  • What does the installation process actually involve?

    It starts with a home assessment and heat loss calculation, then moves to equipment selection, outdoor unit placement, pipework, and electrical work. The job finishes with refrigerant charging, weather compensation setup, and a full commissioning test to confirm the system runs correctly.

More questions about Air Source Heat Pumps?

Arrange a Heat Pump Assessment

Tell us about your home and we’ll arrange a local installer to evaluate the load, size the system for Aurora’s altitude, and put the full scope in writing before anything is booked.

Request an Assessment